6 Steps How To Install Oil Water Separator On Air Compressor with Ultimate Guideline

An oil-water separator is one of the most essential tools to maintain an air compressor system. To determine and comply with the system of air compressors, you must have an oil-water separator or filter. Because if oil or water remains in your air compressors, it can damage your tool and affect its lifespan.

It is designed thus that it can take aside the solid/liquid/micro components before it reaches your tools. So, get an oil-water separator to protect your air compressor systems. Can’t find a proper method of installation of an oil-water separator? Below we will discuss oil waters definition, How To Install Oil Water Separator On Air Compressor, how its function, and the maintenance.

Table of Contents:

• What is an Air Compressor Oil/Water Separator?
• Tools That You Need Before Installation
• How To Install Oil/Water Separator On Air Compressor?
• Maintenance
• FAQs [Frequently Asked Questions]

What is an Air Compressor Oil Water Separator?

An oil-water separator is also known as a condensate separator. Yes, you got it right. It is a tool that works for the separation of liquids (oils and water) from air compressors. You can also use it for tanks, filters, and dryers to drain out oily and watery condensate. Generally, separators are used for removing specific contaminants like oil, water, water vapor, oil vapor, and solid particles.

Tools That You Need Before Installation Oil Water Separator:

Before you start the installation, you need to have some tools to fully set up the oil/water separator. There are:

1. A gear for ear protection,
2. Different sized couplers plugs for using as quick connector,
3. You also may need crescent wrench and thread seal tape or teflon if you can’t tight the connectors properly.
4. Moreover, it will be better if you have 90 degree elbows to tighten the hose in a comfortable position.

How To Install Oil Water Separator On Air Compressor?

As there will be noise while processing, wear the gear for your ear protection. You should also turn off the main power switch before you start. Now, let’s take a look at the steps of installation.

• Step:1

At first wrap thread tape around the quick connectors and make proper Teflon. Thus it will seal the air coming in between the coupler and the 90 degree elbow.

• Step:2

Next, screw out the coupler (male plug connector) in the 90-degree elbows inlet hole and fit it. Then you can use a wrench to tighten it more.

• Step:3

After that, place the separators’ inlet hole to the 90-degree elbows outlet hole, screw, and tighten it up. At this moment, don’t forget to use Teflon. If it is hard to tighten with your hand, you can tighten it with a wrench.

• Step:4

Now, with the same process use another 90-degree elbow in the separators’ outlet hole.

• Step:5

Next, take out the hose tube from the air compressor and attach to it. Use a wrench to tighten it more.

• Step:6

At last, pin the oil/water separator up to the air receiver tanks’ input, from where you have unplugged the hose.

And finally done! It is ready to use.

Oil Water Separator Maintenance

• Keep Viscosity in Limit to prevent clogging of the separator. Discharge the removed separated liquids outside the separator and clean the internals with water.

• Keep an eye on heating the device for a good lifespan of tools.

• Generally inflammable elements are used in this type of tools. So, it will be safe if you keep it far away from fire.

• Check the oil-water level before using.

• Check leakage and effluent to prevent failure of workings and occurrence of accidents.
• Try to replace the separator at least every one year or more often.

FAQs [Frequently Asked Questions]

• Why Do I Need an Oil/Water Separator for My Compressed Air System?

An oil-water separator can usually be found connected to the line between your air compressor and the end of hose. It requires different system pressures so it is determined depending on your system and removes the redundant elements. Thus your air compressors’ volume becomes high and safe.

• Difference of Oil-Water Separators and Water Separators

They are the same product. Though these are commonly referred to as different tools, they more accurately provide the same process and function to do work. You can define it by the internal setup of the separator. An oil-water separator just has the internal setup of density removing oils.

• How does an Air Compressor Oil-Water Separator Work?

A brief source under the cooler with air conditioner, air dryer, any air receiver tank, filter and any other centralized trap throughout the system. It collects condensate from the air compressor tank, filter and dryer then removes the oil from the water before draining the water.

Final Words:

If oil or water reaches your pneumatic tools, serious damage can occur which will result in a short lifespan. You may bear a large cost. So oil and water must collect somewhere in your compressor. The only solution is an oil-water separator. So, get one fast! If you have any questions about oil-water separators, you can contact us. Aren’t you sure which oil/water separator is right for you? Here we are. We will help you to choose the right one for your air compressor system and your working environment.